How to Change a Watch Strap
Two tools, five minutes and a different watch by dinner.

A new strap is the quickest (and most wallet-friendly) way to get a second watch. Steel on Monday, leather by the weekend. The job takes two small tools, about five minutes and a little nerve the first time. Here's how we do it at the bench.
- Time
- About five minutes
- Tools
- A pin pusher and a forked spring bar tool, often one tool with both ends
- Best on
- Drilled lugs, which make removal much easier
- Before you buy
- Match the strap to your lug width, measured between the lugs in millimeters
What you need
- A pin pusher. A fine steel pin that fits the hole drilled through the side of each lug.
- A forked spring bar tool. The fork catches the shoulder of the spring bar so you can compress it without slipping.
- The new strap, with its spring bars already fitted. Many straps now come with quick-release spring bars, which make the job even easier.
- A soft cloth to lay the watch on, face down, and a strip of low-tack tape over the lugs if you want insurance against a slip.
Taking off the bracelet

Every bracelet and strap is held on by a spring bar: a steel tube with a spring-loaded tip at each end. The tips sit in small holes on the inside of the lugs. Push a tip back into its tube and that side of the bracelet comes free.
Do the work with the watch face down on a soft cloth. We've drawn it face up, with the case see-through, so you can watch the spring bar move.
- Find the hole. On drilled lugs, there's a small hole on the outside of each lug, in line with the spring bar.
- Press. Seat the pin pusher in the hole and press gently, straight in. You'll feel the tip give as it retracts into the tube.
- Tilt the end link out. Keep the pressure on and ease that side of the bracelet down and away from the lug. Then press in the tip on the other side, and the end link comes right out.
- Repeat at 12 o'clock. Then set the bracelet aside with its spring bars still in the end links. They're sized for the bracelet, and that's where they belong.
Fitting a leather strap

The buckle half goes on at 12 o'clock, the long half with the holes at 6. Start with whichever you like.
- Check the spring bar. It should sit centered in the strap, with an equal length of tip showing at each side.
- Seat one end. Angle the strap and slip one tip into its lug hole.
- Compress the other. Catch the opposite tip in the fork and push it in toward the strap until it clears the lug.
- Swing it home. Bring the strap level between the lugs and let the tip ride along the inside of the lug until it finds the hole. It clicks into place.
- Pull to check. Give the strap a firm tug. Nothing should move. If it does, the tip is resting against the lug rather than in the hole. Do it again.
A few things we've learned
Go slowly the first time. Almost every scratched lug comes from a tool that slipped while someone was rushing, and tape costs nothing.
No holes in the lugs? Removal works with the fork alone. Slide it between the strap and the lug, catch the shoulder of the spring bar and push the tip in. It takes more patience, but it's the same move in reverse.
Spring bars wear out. If one is bent or has lost its snap, replace it. It's the only thing keeping the watch on your wrist.
Where to start
A bracelet watch on leather is a different watch. Our Chestnut leather softens a steel diver and warms up a black dial. For something lighter, try the Black RAF or Admiralty Gray nylon. For water, the Bonetto rubber.
Frequently asked questions
What size strap do I need?
Your lug width, measured between the lugs in millimeters.
Can I change a strap without tools?
We wouldn't. It's easy to scratch the lugs, and a spring bar tool costs less than a polish.
Do I need new spring bars?
Not if they're straight and spring back firmly. Keep the bracelet's spring bars with the bracelet.
What if my lugs aren't drilled?
Use the forked end. Slide it between the strap and the lug, catch the spring bar's shoulder and push the tip in.